Eureka Tents Tent Pine Lodge User Manual

3. Continue with the remaining three roof poles  
and main pole on the opposite side to  
complete the roof assembly.  
See fig 5.  
5. Raise the tent. Start on one side and insert  
gray wall poles into the elbows. Locate the web  
ring/pins attached to the floor of the tent. Insert  
a pin into the base of each pole. See fig 9 & 10.  
Repeat on the other side until the tent is at full  
height and freestanding.  
Assembly Instructions for  
the Pine Lodge Tent  
fig 5  
Component List:  
fig 10  
1 Tent Body with Guy Ropes, 3 Main Poles, 6 Roof Poles, 6 Wall Poles, 4 Fan Door Poles,  
1 Carry Bag, 1 Stake Bag/Stakes, 1 Pole Bag  
6. Stake the tent down. Stake  
out the corner rings first. As  
you work your way around the  
tent apply tension to square  
the tent and pull out any floor  
wrinkles. Align the center  
poles with the corners and  
stake out web side rings. See  
fig 12. [If you have the  
1. Remove from the carry bag and separate all the components. Unroll and unfold the  
fabric top side up, on a clean, dry space and open the doors. If windy, stake down the  
windward corner. See fig 1.  
4. Attach the fabric to the roof  
frame. Hook the shockcorded  
J-hooks to the brass rings  
and to the holes in the  
elbows.  
fig 6  
fig 1  
Fly/Awning option, now  
complete 'Step IV'.]  
Important: Make sure the  
bottom front of the tent is in a  
straight line, from corner to  
corner.  
fig 14  
Main  
2. Assemble the shock corded  
fig 12  
fig 13  
poles  
fig 7  
fig 8  
poles and divide according to  
fig 2  
size and shape. Take care;  
make sure that each pole  
section is fully seated into the  
next. Do not allow the  
sections to snap together as  
this can damage the ends.  
See fig 2.  
7. Assemble the fan door frame. Slide the  
fiberglass fan door poles, rubber end up, into  
the bottom of the door sleeves. Insert pins  
from the web loop into the bottom of these  
poles. See fig 12 & 13. Tuck the door into its  
perimeter envelope.  
Roof  
poles  
Snap the web clips to the poles. It is best to start in the center and work your way out. You  
must do this now because you won’t be able to reach the clips and hooks once the walls  
are raised. See fig 6, 7 and 8.  
Wall  
poles  
Fan Door  
poles  
There is a web loop on each side of the fan  
door, stake these down.  
NOTE: If you intend to install the optional fly/awning, do now. It is far easier to attach the  
fly/awning while the roof is still on the ground.  
8. Attach the splash guard. To provide an  
extra layer of protection, there is a flap that  
runs across the bottom near the inside of  
the door. Attach the J-hooks from this flap to  
loops at the front corners. See fig 14.  
3. Build the roof frame. Inset three black roof poles into the nylon elbows on one of  
the main poles at A, B and C. This forms the outer ridge. Move to the opposite side  
and again fit the same three poles into the nylon elbows of a second main pole at D,  
E and F. This forms one half of the roof. See fig 3 and 4.  
Installation of the Optional Fly/Awning:  
Step I: Lay the Fly out on the ground in front of the tent, with the awning to the far front.  
Step II: With 2 people, grab the rear corners of the Fly & walk it over the top of the frame  
from front to back.  
F
fig 14  
C
Step III: There are 6 frame extensions, 1 each at the ends of the center ridge and eave  
poles front and rear. See fig 9 positions A,B, D, E, F- position C not visible. At the rear of  
the Fly, slide the 3 extensions in to the pockets sewn on the Fly (positions A, B, C).  
Repeat this step along the front of the tent at positions D, E & F. [Continue with tent  
set-up at number 5 'Raise the tent'.]  
fig 3  
YOUR TENT IS READY !  
Guy Out: This tent has very large straight walls that act differently in high winds. If there  
are high winds, carefully follow the guy out instructions on the back side of this sheet.  
B
E
Power Port: Open zipper and run extension cord  
through opening. Close zipper so that it rests  
next to the extension cord. Make sure the  
zipper cover is not twisted or tucked. The cover  
must lay flat against the outside of the tent to  
keep out rain. See fig 15.  
Step IV: Once the tent is completely set up and staked out, insert the awning poles and  
stake them out. See fig 11.  
A
D
E
B
F
fig 9  
Take Down: Remove the poles from the fan door.  
Pull up all stakes. Pull wall poles off of the pins  
fig 15  
NOTE: When properly seated, the small  
spring on the pole will click into place.  
fig 11  
and remove poles. Remove roof poles. Collapse  
all poles and stow. Fold the tent onto itself then  
roll up towards the open door and stow.  
A
Options: Floor Saver and Fly/Awning.  
Rev.D 4.09  
D
 

Abocom Digital Photo Frame DPF102 User Manual
Acer Cell Phone F900 User Manual
Acer Laptop 1310 User Manual
Acer Laptop TravelMate 530 User Manual
AD Blood Pressure Monitor UA 767 Plus BT User Manual
ADC Switch UltraWAVE X100 User Manual
Air King Ventilation Hood AK927 User Manual
Alto Shaam Food Warmer EC2 72 User Manual
Ask Proxima Projector DP5950 User Manual
Behringer Car Stereo System B205D User Manual