Eureka Tents Tent JUNO 3XTA User Manual

With the tent secure, drape the fly over the tent body. The fly only fits  
on the tent one way. Position the fly over the tent with the vestibule  
wing sections over the doors and with the ! section over the all mesh  
end of the tent. Reach under the fly and connect the hook and loop  
tabs to the tent poles. See fig 7.  
C
B
ASSEMBLY INSTRUCTIONS  
for the JUNO 3XTA TENT  
Connect the four corner buckles on the fly to their mates on the tent  
webs. Do not fully tighten down any of the webs just yet.  
See fig 8.  
D
Component List:  
A
1 Tent Body,  
2 Tent Poles,  
1 Carry Bag,  
1 Tent Fly,  
1 Stake Bag/ Stakes  
fig 3  
Unroll and unfold the tent with the floor on the ground.  
Remove the fly and set it aside. Do not stake the tent  
down yet. In windy conditions, we recommend that the  
mesh end should face into the wind and that you stake  
down one corner of this end.  
Join the shock-corded poles together. Try to prevent  
pole sections from snapping together, as this can  
damage the pole ends. NOTE: Make certain each  
insert end has seated firmly into each plain end.  
See fig 1.  
Start at the front of the tent at D, grasp the  
end of the pole in one hand and the web  
loop in the other. Push the pole from D to B  
creating an arc. Insert the pin into the pole  
ferrule to tension the tent across the seam  
line. Repeat with the other pole; C to A.  
See fig 3 and 4.  
fig 7  
fig 8  
At the front of the tent, pull the stake out loop on the vestibule taut  
and stake it down. Make sure that the vestibule is tight across the  
door. Repeat with the second vestibule at the rear of the tent.  
See fig 9.  
fig 4  
fig 5  
Raise up both poles and attach the peak of  
the tent to them. Capture the poles, where  
they cross, with the tent clips. Then attach  
all remaining clips to the poles.  
See fig 5.  
C
B
Your tent is now free-standing, place it in  
location that has enough room for the fly  
and stake it down through the corner rings.  
Stake the opposite corners while applying  
tension to smooth the floor wrinkles.  
See fig 6 and 7.  
fig 6  
A
D
NOTE: General purpose stakes are included  
but snow or sand stakes can be purchased  
at a Eureka! dealer.  
fig. 1  
fig 9  
At the front corner of the tent- A,  
slide the ball end of one of the  
aluminum poles into the rod  
sleeve. Angle the pole to the  
opposite corner; A to C. At corner  
B, repeat with the second pole  
and sleeve; B to D.  
With the vestibule wing sections staked down and tight, go to the open  
side of the tent, pull out the vent and hold it in place with the hook  
and loop tab. Then adjust and tighten all the remaining side release  
buckles.  
fig 7  
Your tent is now ready for use.  
NOTE: In strong winds, tie extra cords to the storm loops on the fly and  
stake down so that the cords are tight.  
See fig. 1 and 2.  
Take down: Pull up stakes and open doors. Remove the fly. Pull pins out of  
the poles. Un-clip, collapse the tent poles and stow in the pole bag. Fold the  
tent and the fly. Roll up both along with the pole bag towards the door and  
fig. 2  
stow all in the main bag.  
REV.B 2-10  
 

Acer Personal Computer RC500L User Manual
AEG Power Supply 6000BP User Manual
Agri Fab Lawn Aerator 45 0298 User Manual
American DJ DJ Equipment TP DMX24F User Manual
American Standard Hot Tub T038990 User Manual
Asus Computer Accessories A7V8X LA User Manual
Atlantis Land Switch A07 ES3628C User Manual
Ayre Acoustics CD Player CX 7EMP User Manual
Azden Digital Camera 305UPR User Manual
Behringer Car Speaker b1030 User Manual