ABC Office Paper Shredder 802CC User Manual

The Shredder Company  
Schleicher International  
POSTFACH 1420  
D-88672 MARKDORF/BODENSEE - GERMANY  
Typ/Type/Type/Tipo: 648 / 649  
Serie/Series/Série/Serie: 648 / 649  
Vor der Inbetriebnahme die Bedienungsanleitung durchlesen!  
Before operating, please read the Operating Instructions!  
Veuillez lire le mode d’emploi avant la mise en service!  
Voor de inbedrijfstelling de gebruiksaanwijzing doorlezen!  
Leer las instrucciones de uso antes de la puesta en servicio!  
Antes de pôr a máquina em funcionamento leia as instruções de operação!  
Prima della messa in funzione leggere attentamente le istruzioni!  
Bedienungsanleitung  
Operating instructions  
Instructions d’opération  
Gebruiksaanwijzing  
Instrucciones de uso  
Instruções de Operação  
Istruzioni per l’uso  
(Seite 2-4)  
(page 5-7)  
D
GB  
F
(page 8-10)  
(pagina 11-13)  
(página 14-16)  
(página 17-19)  
(pagina 20-22)  
NL  
E
P
I
Schaltplan / Wiring Diagram / Plan de montage / Schakelschema  
(Seite / page / pagina  
Diagrama eléctrico / Esquema electrico / Schema Elettrico página / pagina 23-24)  
 
GB  
Schleicher International  
OPERATION  
OPERATING FUNCTIONS (Figs. 1, 2 and 4):  
1 = Mains switch (Emergency-stop) (fig. 1)  
This switch turns the machine either on  
(position „1“) or off (position „0“).  
2 = „Cutting system forward“  
pushbutton (fig. 2)  
OPERATING THE MACHINE:  
Neverfeedtheshredderwithaquantity  
of paper exceeding the maximum  
indicated in the technical details.  
Should the machine be overfed, follow  
the instructions under „AUTOMATIC  
To start, switch on the unit by operating the mains  
switch(1)(fig.1).Thepilotlampmarkedreadyfor  
operation“ (5), as well as the red stop-button „S“  
(3) (fig. 2) will light to indicate that the machine is  
ready for operation.  
RESPONSE  
IN  
CASE  
OF  
Pressingthisbuttonstartsthecuttingsystem.  
Material can now be fed to the shredder.  
3 = „Cutting system stop“  
OVERLOADING“.  
The paper tray may not be used as a  
step ladder or as a seat. Danger of  
tipping over!  
AUTOMATIC RESPONSE  
IN CASE OF „OVERLOADING“:  
pushbutton (fig. 2)  
Pressing this button switches the shredder  
off, thereby halting the cutting system.  
4 = „Cutting system reverse“  
pushbutton (fig. 2)  
Pressing this button starts the cutting system  
in reverse.  
5 = Pilot lamp (fig. 2)  
In case you accidentally overload the shredder, it  
willautomaticallyalleviatetheproblemasfollows:  
1. Thecuttingsystembecomesjammed.Thepilot  
lamp (6) (fig. 2) lights up.  
2. The cutting system runs briefly in reverse,  
thereby freeing the material to be shredded.  
3. Thecuttingsystemautomaticallyswitchesback  
to forward mode.  
FEEDING CRUMPLED PAPER  
(MODEL 852CC):  
In order to avoid a reduction of user  
safety by increasing the height of the  
hopper side panels, and in order to  
allow for filling the hopper while  
standing on the floor, the height of the  
hoppersidepanelsisnotincompliance  
with EN 294:1992.  
a) „ready“  
Continouslylightswhenthemainsswitch  
(1) is operated.  
The machine repeats this process until all the  
material has been shredded satisfactorily.  
b) „motor protection“  
The deviation from EN 294:1992 is  
identified with a yellow-black mark.  
1. Fill the hopper with crumpled paper.  
Note: The crumpled paper can be dropped  
directly from the wastepaper basket into the  
hopper of the machine. The apportioning wings  
preceding the cutting mechanism ensure more  
or less uniform distribution of the paper.  
Attention: The wastepaper basket is no refuse  
tin and should not be emptied into the machine  
thoughtlessly - in no way can the machine  
destroy bottles, pens, pencil sharpeners etc.  
2. Press the pushbutton switch „forward“ (2) (fig.  
2). Thecuttingsystemrunsandbeginstoshred  
the paper.  
Flashes when the motor is overloaded.  
While the motor is cooling down, the  
machinecannotbeswitchedontoforward“  
run.  
EMPTYING THE COLLECTING BAG (Fig. 3):  
When the collecting bag is full, the machine turns  
off automatically. The pilot lamp (7) (fig. 2) lights  
up. Empty the collecting bag as follows:  
- Open the door and take out the sliding frame  
with the collecting bag.  
6 = Pilot lamp „paper jam“ (fig. 2)  
Lights when too much paper is fed to the  
cutters (see description „AUTOMATIC  
RESPONSE IN CASE OF OVER-  
LOADING“).  
- Remove the rubber band, take out the full bag  
and dispose of contents.  
- Put the empty bag from below through the  
sliding frame and put the edges of the bag  
approx. 10 cm over the frame outwardly.  
- Fixthecollectingbagwiththerubberbandatthe  
sliding frame.  
- Move back the sliding frame with the collecting  
bag and close door.  
Note: The machine will only run with closed door!  
7 = Pilot lamp (fig. 2)  
a) „door open“/„hopper open“  
Lights when the door is not closed or when  
the hopper is open. The machine then  
switches off automatically and it cannot be  
started as long as the door is open or the  
hopper is open.  
Note: Do not feed any smooth paper until the  
crumpled paper is completely shredded.  
3. To switch the machine off press the red stop-  
button (3) (fig. 2).  
b) „collecting bag full“ (fig. 2)  
Lights as soon as the collecting bag is full  
andneedstobeemptied. Atthesametime  
the machine switches off automatically.  
8 = Light barrier (forward operation) (fig. 4)  
The shredding operation is started as soon  
as a sheet of paper passes through the feed  
slot.  
FEEDING SMOOTH PAPER:  
- Feed smooth paper through the opening at the  
lower part of the hopper (model 852CC) or  
throughtheopeningofthehopper(model802CC)  
to the cutting system.  
- Machine switches automatically to forward and  
draws paper in.  
- The machine switches off automatically after  
shredding.  
I
S
MAINS SWITCH  
1
3
4
2
5
6
7
fig. 1  
fig. 2  
fig. 3  
6
 
GB  
Schleicher International  
MAINTENANCE  
CUTTING SYSTEM MAINTANANCE:  
CLEANING THE PHOTOCELLS (8) (Fig. 4):  
If paper particles should come to rest in the inlet  
guide (for example after a paper jam) it is possible  
thatthemachinewillnotturnoff, duetothebroken  
light barrier.  
Afterabout2hoursofcontinuousoperationrun  
thecuttingsysteminreverseforabout30seconds  
and,atthesametime,spraysomeoftheenclosed  
special oil onto the cutting system.  
Toremovethesepaperstripsandalsotocleanthe  
photocell, pass another sheet of paper through  
thefeedslot, orswitchthemachinetoreverseand  
wipe both „eyes“ of the photocell with a brush.  
ENERGY SAVING TIP:  
Be certain that the machine is turned off overnight  
(mains switch (1) (fig. 1) switched to „0“).  
8
fig. 4  
MALFUNCTION  
TECHNICAL DATA  
TAKING OUT EXCESS PAPER  
IN CASE OF OVERLOAD:  
If the shredder has stopped due to an overload  
(motor protection) take the excess paper out of  
the inlet as follows:  
Note: When the motor is overloaded, only the  
forwardruniscutoff.Totaketheexcesspaperout  
of the inlet opening, the cutting system may at any  
time be switched on „reverse“.  
Cutting width:  
802CC:  
852CC:  
Cutting capacity:  
802CC:  
1.9x15 (cross-cut)  
3.8x40 (cross-cut)  
35-40 sheets (70 g/m2)  
70-80 sheets (70 g/m2)  
444 mm  
3.9 kW  
400V/50Hz  
1. Depressthereversepushbutton(4)(fig.2).The  
material is released.  
2. Liftupthehopper. Thepilotlampdooropenor  
„hopper open“ (7) (fig. 2) will light.  
3. Remove the excess material by hand from the  
inlet guide.  
FAULT CHECKLIST:  
If the machine is not functioning properly, you  
should check the following:  
- is the plug conneted to the mains?  
- is the mains switch (1) turned on?  
- is the door closed?  
852CC:  
Working width:  
Power:  
Supply voltage:  
230V/50Hz  
415V/50Hz  
Note: In this case, there is no danger of injury  
as all circuits are interrupted when the hopper  
is lifted and the machine cannot be started.  
- is the collecting bag full?  
The bag has to be emptied.  
- is the motor overloaded?  
220V/60Hz  
200V/50Hz  
200V/60Hz  
PleaserefertothesectionheadedMotorFault“.  
- is there a phase failure?  
Pre-fusing:  
(gl fuse, type 1 assignment)  
MOTOR FAULT:  
Themachineisequippedwithathermallyprotected  
motor. Should this motor be overloaded, it will  
switch off automatically. In such case the pilot  
lamp „ready“ (5) (fig. 2) flashes.  
After a cooling down period of approx. 10 minutes  
(depending on the room temperature) you can  
restart the machine and continue shredding.  
Checkthethree-phasefuseatthepowersupply  
socket, and replace if necessary.  
400V-415V/50Hz:  
220V-230V/50-60Hz:  
200V/50-60Hz:  
Width:  
Depht:  
Height:  
16 A  
25 A  
25 A  
750 mm  
550 mm  
Ifyoustillcannotisolatethefaultaftercarrying  
outallthesechecks,pleasenotifyourcustomer  
service department.  
802CC:  
1275 mm  
852CC:  
1600 mm  
Noise level:  
Weight:  
approx. 75 dB(A)  
802CC:  
852CC:  
approx. 185 kg  
approx. 201 kg  
ACCESSORIES  
Description  
Plastic bag, 600 x 380 x 1100 x 0,6 mm  
Lubrication bottle, 125 ml  
Order-No.  
80946  
99943  
Note: For orders of special accessories and spare parts, please contact your dealer.  
7
 
Schleicher International  
Konformitätserklärung  
Certificate of Conformity  
Attestation de Conformité  
Bezeichnung der Maschine:  
Type of machine:  
Déscription de la machine:  
Datenshredder  
Document Shredder  
Destructeur de Document  
Modelle / Models / Modèles:  
Typen / Types / Types:  
intimus 802CC  
intimus 852CC  
648 / 649  
Hiermit wird bestätigt, daß o. g. Geräte den Anforderungen der Maschinen-Richtlinie 89/392/EWG, sowie  
der EMV-Richtlinie 89/336/EWG (Klasse B) einschließlich allen bis heute veröffentlichten Änderungen  
bzw. Nachträgen entsprechen. Die o. g. Geräte entsprechen folgenden Normen bzw. Richtlinien:  
WedoherebycertifythattheabovementionedproductsmeettherequirementssetforthinEEC-Guidelines  
89/392 and EMC 89/336 (Class B) including all changes and addendums to date thereto. The above  
mentioned products meet the following standards and guidelines:  
Nous Vous Confirmons que les appareils cités ci-dessus correspondent aux exigences des directives 89/  
392/CEE ainsi qu’ à la directive CEM 89/336/CEE (Classe B), ci-inclus toutes les modifications ainsi que  
tous les suppléments publiés jusqu’à ce jour. Les appareils mentionnés correspondent aux normes citées  
ci-après:  
EN 292-1, Ausgabe / dated / en date du 1991  
EN 294-1, Ausgabe / dated / en date du 1992  
EN 60204-1, Ausgabe / dated / en date du 1993  
EN 55011, Ausgabe / dated / en date du 1993  
EN 61000-4-2 /-4 (IEC 1000-4-2 /-4), Ausgabe / dated / en date du 1995  
ENV 50140 (IEC 1000-4-3), Ausgabe / dated / en date du 1993  
November / November / Novembre 2000  
ppa. D. Schuster  
i. A. J. Erlecke  
The Shredder Company  
Leiter Technik  
Leiter Elektrik  
POSTFACH 1420  
D-88672 MARKDORF/BODENSEE - GERMANY  
Head of Technical Dpt.  
Head of Electrical Dpt.  
Responsable Dép. Technique  
Responsable Dép. Electricité  
Dieses Papier ist aus 100 % Altpapier ohne optische Aufheller hergestellt  
This paper made from 100 % unbleached recycled paper  
Papier recyclable à 100 %  
 

Acer Personal Computer M5810 User Manual
Agilent Technologies Computer Hardware E5250A User Manual
Agilent Technologies Network Router 35670A User Manual
Agilent Technologies Projection Television 8472B User Manual
AG Neovo Flat Panel Television S 19A User Manual
Alamo Lawn Mower FALCON 15 10 User Manual
Alto Shaam Oven 1000 SK III User Manual
American DJ DJ Equipment Ruby Star User Manual
Audiovox Remote Starter 128 8128 User Manual
Beko Microwave Oven MWB 2000 EX User Manual